Manual and Automated Metal Seated Valve- Metalseat

Flowserve API 6D Gate Valve is world renowed. The Improved sealing and tight shutoff performance with bi-mdirectional sealing in both upstream and downstream sides. Minimized wear and tear and increased life of sealing components through low-friction, slab gate guiding mechanism. Enhanced strength over weight ratio provided by robust assembly with optimized structural design that uses engineered ribs profile.

Application: Oil and gas: liquid products and secondary recovery pipeline; midstream and downstream pipelines, including valves for: mainline block, tank and station, manifold, launcher/receiver trap, meter bypass, emergency shutdown, transmission and distribution

WORLD BEST MANUFACTURING FOR METAL SEATED BALL VALVE AND SOFT SEATED BALL VALVE. SUITABLE FOR HIGH TEMP, HIGH PRESSURE, CRITICAL CONDITION. ALL APPROVAL RECEIEVD. 

Details:

• Metal Seated ,Lubricated Type, Pressure Balanced
• Tight Shut off
• API – 6D
• Fire Safe

Flowserve Manufacture High Performance Triple Off Set Butterfly Valve providing repeatbale and long lasting shut off.  It can adress critical  and server service application. The size range from 3 to 24 Inch and temerature can be managed till 800 degree. The body design can be wafer, lug, double flange (Short and Long). The valve is also suitbale for top entry cryogenic and high pressure

FLOWSERVE HAS WIDE RANGE OF GATE/GOBE CHECK VALVE

Bolted Bonnet Globe and Angle Valves, Stop and Stop-Check (Non-Return) and Bolted Cover Piston Check 

Pressure Seal Bonnet Globe and Angle Valves Stop and Stop-Check (Non-Return) 

Pressure Seal Cover, Piston Check Valves 

Equiwedge® Gate Valves 

Flite-Flow® Globe Valves, Stop and Stop-Check (Non-Return) 

Flite-Flow® Piston Check ValvE

Tilting DIsc Check Valve

Globe Stop Valve tec

The  swing  check  valve  is  a  uni-directional  valve  that  allows  flow  in  one direction  and  it  does  not  allow  the  flow  in  reverse  direction.  This  is generally used in pump discharge lines at the downstream of the pump to prevent  back  flow  of  water  to  the  pump  in  the  event  of  tripping  of  the pump  due  to  electricity  failure.  This  is  required  to  avoid  damage  to  the pump. 

When the pump is running, the flow from the pump upstream of the valve will  open  the  valve  disc.  The  angle  of  valve  opening  will  be  primarily governed by the forward flow/ velocity of water from the pump. 

Smooth  closure  of  the  valve  is  ensured  by  using  a  counter  weight.  The valve  can  be  supplied  with  hydraulic  dash  pot  to  prevent  disc  slamming and water hammer

This  valve  is  operated  by  the  hydraulic  cylinder  with  power  pack  with control  circuit.  The  hydraulic  cylinder  opens  the  valve  as  soon  as  pump motor starts. When the pump motor stops or trip due to electrical failure, suitable  control  signal  is  fed  into  the  hydraulic  power  pack  to  close  the valve  immediately  and  prevent  back  the  flow  into  the  pump.  This arrangement eliminates the needs for two separate valves which act as a shut off valve and non-return valve

Noble Alloy Valve’s line of forged and precision cast ball valves provides the ultimate in flexibility and value. With its uniquely interchangeable balls and seats, these valves can be easily retrofitted for changing service conditions. All valves meet appropriate ASME, API and MSS design and performance criteria. The v-port ball may be specified in 30° and 45° configurations for either metal or soft seat valves. Patented conical metal seating eliminates matched lapped sets, enabling virtually unlimited trim combinations including soft seats.Bi-directional design allows easy reversal of flow direction .Three-piece body construction accommodates in-line service or retrofit.Patented live-loaded packing with back-up adjustment is standard on all 3D valves.High end alloy valve models are available in high quality investment cast or forged/100% machined bodies.ASME Class 150 to 1500 • Full port • Nobleized surface hardened ball and stems • Buttweld, socketweld and threaded end connections. These also manufacture Titanium Valves 

The RSBV uses a unique helix system that opens and closes the valve without rotation. The linear only operation of the stem makes it an excellent choice for frequent cycling.  Each linear operation, from opening to closing and back again, is a friction-free movement between seat and ball that significantly reduces valve wear and keeps routine maintenance to a bare minimum.Whether your needs call for molecular sieve switching, isomerization, thermal oil, high/low temperatures or critical services, the RSBV provides an unmatched level of robustness, reliability, and convenience

THESE ARE SPECIALISED BALL VALVE USED IN CRITICAL APPLICATION. TEHSE ARE FOR SPECIAL APPLICATON LIKE HIGH PRESSURE, MULTI PORT, CHLORINE SERVICE, FUGITIVE EMISSION, CRYOGENIC VALVE, ASEPTIC VALVE, HIGH PURITY, TANK BOTTOM VALVE